bettyneedle20

Fiat 500 Replacement Key Fob It might be time to change the battery if your 500 remote key fob isn't working. If you do replace the battery and it is still not working the issue could be elsewhere. United Locksmith specializes in the production of new keys for classic vehicles. We have the tools and parts needed for this job. Dead Coin Battery A dead battery is the primary cause of your Fiat 500 keyfob not locking or unlocking the doors. The key fob is equipped with the battery of a coin-cell which will quickly drain if it is not frequented enough. If your remote started to show signs of weakening such as a loss of range and then completely stopped working, the battery is probably dead. The battery inside the key fob is secured by metal clips that hold it in place. If the clips aren't secure, it could lead to problems with contact, which can prevent the remote from receiving power. Use a flathead screwdriver break open the retaining clip and remove the battery. Be sure to choose a replacement with the same type of voltage, size, and specification as the original battery. Water exposure can also cause the key fob to become corroded or damaged. Even a short bath in soapy water may damage the electronic chip inside. It's best to keep your key fob in a dry area. Water Damage If your key fob isn't operating properly, it could be due to water damage. The rubber seals on key fobs protect them from getting damaged by a slight splash or drizzle of water. However, it's essential to keep the car keys away from the ocean, washing machine, and pool. The key fob comes with an electronic chip which sends an alert to the immobilizer system of your vehicle. The chip allows the 500 to lock and start. If it gets wet, it will no longer work. You can try cleaning the inside electronics of your keyfob using isopropyl alcohol, or an electronic cleaner to see whether they're still working. It is recommended to replace a key fob in the event that it is submerged in salt water rather than try to repair it yourself. A replacement fob might cost you a little bit however, it's less expensive than paying to have your Fiat 500 towed to a dealer and fixed there! Plus, you can do it yourself in several easy steps. Make sure you have the correct type of battery prior to opening your keyfob. You can find step-by-step instructions for any car keyfob on the internet. Faulty Chip The chip inside the key fob communicates with your vehicle's immobiliser to ensure that your car is only capable of starting when the correct key is used. If the chip is damaged, or corrupted the car will not start no matter what you do. Water damage or a dead battery are the two most frequent causes of defective chips. TheKeyLab is best to hand over the job to a professional locksmith, who can repair the chip quickly and at reasonable cost. If your key fob does not work after being exposed to water that is clean from the tap or rain, remove the battery. Wipe down the electronic component with a paper towel. If the key fob fails to work, it is likely an issue with the chip and is required to be replaced. Many people will seek out their dealer when in need of a new Fiat key fob, however it can be a expensive alternative. United Locksmith is the best option for you if would like to have your Fiat key fob repaired at a reasonable price. We have the tools and knowledge necessary to repair your Fiat key fob in a quick and professional manner. Faulty Receiver Module Fiat key fobs transmit an electrical signal to the vehicle that will unlock and close doors (and start the car if it has an automatic transmission) up to 50 feet. However there are a few things that could cause the fob to stop working. This could be due to a dead coin battery damaged by water buttons, worn ones or a problem with the receiver module, and signal interference or an electronic chip that is malfunctioning. If the fob is in a pocket which has suffered extreme trauma (such as being dropped on a hard floor or being washed in a washing machine), it may not be able to communicate with the Body Control Module (BCM) of the vehicle. This is because the BCM is a secure system that can only accept a signal from a genuine key and not accept any other. You will need to replace the fob in case this happens. A professional locksmith can handle the entire replacement process including programming a new one for your 500. In fact, they can provide you with a clone key that functions the same way as your original fob (and costs only a fraction of the price).